Question Solved1 Answer computer architecture 9. Write an assembly language program for the following expression using is computer Instruction set and interpret same to the flow of IAS computer using register transfer notation. A=B* C+ (D-E)/2 The data variables B, C, D and E are available at location 501, 502, 503 and 504, respectively. The result A should be stored from 504 onwards.

Problem 1 Lamport Logical Clock (12 credits) For each process p € {A, B.C.D.E.F) determine the logical time {CA.C. Cc. Co. CE, CF) at the end of the time/event diagram according to Lamport's Logical Clock algorithm. Write the final value of clocks in the table below. CA Св Сс D CD CF Logical Time CA Св Сс Ср CE CF

Air at 80 degrees Fahrenheit and 14.7 psia with a mass flow rate of 0.6 lbm/sec enters a compressor and leaves at 70 psia and 430 degrees Fahrenheit through an exit area of 0.007 ft^2.  The measured heat interaction rate with the 80 degree Fahrenheit factory room is 3 Btu/sec.  Use constant Cp = 0.24 Btu/lbm oF a) Calculate the compressor work rate.   b) Compute the entropy generation rate for the overall process.  

1 Required information A 20-mm-diameter rod made of the same material as rods AC and AD in the truss shown was tested to failure and an ultimate load of 105 kN was recorded. Use a factor of safety of 3.0. Part 1 of 2 1,5 m D B 3 m -3 m 48 kN 48 kN Determine the required diameter of rod AC. The required diameter of rod AC is mm.

Required information A 20-mm-diameter rod made of the same material as rods AC and AD in the truss shown was tested to failure and an ultimate load of 125 kN was recorded. Use a factor of safety of 3.0. 1.5 m 3 m 48 KN 48 KN Determine the required diameter of rod AC. The required diameter of rod AC is mm

thermo 2 help plz Air, at \( 80^{\circ} \mathrm{F} \) and \( 14.7 \) psia with a mass flow rate of \( 0.6 \mathrm{Ibrm} / \mathrm{sec} \) enters a compressor and leaves at 70 psia and \( 430^{\circ} \) F through an exit of area 0007 . th \( ^{2} \). The measured heat internction rate with the \( 80^{\circ} \mathrm{F} \) factory room is \( ₹ \mathrm{Bth} / \mathrm{sec} \). Use constant \( \mathrm{C}_{p}=0.24 \mathrm{Btw}_{\mathrm{f}} \mathrm{b}_{\mathrm{m}}{ }^{\circ \mathrm{F}} \) a. Calculate the compressor work rate, W. b. Compute the entropy generation rate for the overall process.

Required information Problem 15-4A (Algo) Preparing job cost sheets, recording costs, preparing inventory ledger accounts LO P1, P2, P3 [The following information applies to the questions displayed below] Watercraft's predetermined overhead rate is 200% of direct labor. Information on the company's production activities during May follows. a. Purchased raw Required information Problem 15-4A (Algo) Preparing job cost sheets, recording costs, preparing inventory ledger accounts LO P1, P2, P3 [The following information applies to the questions displayed below] Watercraft's predetermined overhead rate is 200% of direct labor. Information on the company's production activities during May follows. a. Purchased raw materials on credit, $220,000 b. Materials requisitions record use of the following materials for the month. Job 136 Job 137 Job 138 Job 139 Job 140 Total direct materials Indirect materials Total materials requisitions Job 136 Job 137 30h 138 300 119 $ 49,500 32,500 19,400 c. Time tickets record use of the following labor for the month. These wages were paid in cash Job 140 Total direct labor Indirect labor Total labor cost 23,200 6,400 131,000 20,500 $ 151,500 $ 12,300 10,500 37,900 39,200 4,000 101,900 14,500 $ 128,400 Journal entry worksheet < 3 Record raw material purchases on credit. Note: Enter debits before credits. Transaction Record entry 4 Raw materials inventory Accounts payable General Journal 5 Clear entry 6 7 8 Debit 220,000 ***** Credit 11 220,000 View general journal >