Question Solved2 Answers A wind generator with a blade diameter D is generating 80 kW of power at a certain wind velocity v. What is the power generated if the wind velocity doubles?

Question 3 (10 Marks): Consider the following second order system: i(t) = Ac(t) + Bu(t) y(t) = Cx(t). where [1 [k A= B= C k3 ks] Determine the range of values for ki, k2, k3 and kų such that this system is controllable and observable.

Air at 80 degrees Fahrenheit and 14.7 psia with a mass flow rate of 0.6 lbm/sec enters a compressor and leaves at 70 psia and 430 degrees Fahrenheit through an exit area of 0.007 ft^2.  The measured heat interaction rate with the 80 degree Fahrenheit factory room is 3 Btu/sec.  Use constant Cp = 0.24 Btu/lbm oF a) Calculate the compressor work rate.   b) Compute the entropy generation rate for the overall process.  

1 Required information A 20-mm-diameter rod made of the same material as rods AC and AD in the truss shown was tested to failure and an ultimate load of 105 kN was recorded. Use a factor of safety of 3.0. Part 1 of 2 1,5 m D B 3 m -3 m 48 kN 48 kN Determine the required diameter of rod AC. The required diameter of rod AC is mm.

Required information A 20-mm-diameter rod made of the same material as rods AC and AD in the truss shown was tested to failure and an ultimate load of 125 kN was recorded. Use a factor of safety of 3.0. 1.5 m 3 m 48 KN 48 KN Determine the required diameter of rod AC. The required diameter of rod AC is mm

thermo 2 help plz Air, at \( 80^{\circ} \mathrm{F} \) and \( 14.7 \) psia with a mass flow rate of \( 0.6 \mathrm{Ibrm} / \mathrm{sec} \) enters a compressor and leaves at 70 psia and \( 430^{\circ} \) F through an exit of area 0007 . th \( ^{2} \). The measured heat internction rate with the \( 80^{\circ} \mathrm{F} \) factory room is \( ₹ \mathrm{Bth} / \mathrm{sec} \). Use constant \( \mathrm{C}_{p}=0.24 \mathrm{Btw}_{\mathrm{f}} \mathrm{b}_{\mathrm{m}}{ }^{\circ \mathrm{F}} \) a. Calculate the compressor work rate, W. b. Compute the entropy generation rate for the overall process.

Required information Problem 15-4A (Algo) Preparing job cost sheets, recording costs, preparing inventory ledger accounts LO P1, P2, P3 [The following information applies to the questions displayed below] Watercraft's predetermined overhead rate is 200% of direct labor. Information on the company's production activities during May follows. a. Purchased raw Required information Problem 15-4A (Algo) Preparing job cost sheets, recording costs, preparing inventory ledger accounts LO P1, P2, P3 [The following information applies to the questions displayed below] Watercraft's predetermined overhead rate is 200% of direct labor. Information on the company's production activities during May follows. a. Purchased raw materials on credit, $220,000 b. Materials requisitions record use of the following materials for the month. Job 136 Job 137 Job 138 Job 139 Job 140 Total direct materials Indirect materials Total materials requisitions Job 136 Job 137 30h 138 300 119 $ 49,500 32,500 19,400 c. Time tickets record use of the following labor for the month. These wages were paid in cash Job 140 Total direct labor Indirect labor Total labor cost 23,200 6,400 131,000 20,500 $ 151,500 $ 12,300 10,500 37,900 39,200 4,000 101,900 14,500 $ 128,400 Journal entry worksheet < 3 Record raw material purchases on credit. Note: Enter debits before credits. Transaction Record entry 4 Raw materials inventory Accounts payable General Journal 5 Clear entry 6 7 8 Debit 220,000 ***** Credit 11 220,000 View general journal >