Question Solved1 Answer Consider the process flow diagram that we made in class for McDonald’s. To simplify the scenario, imagine that the process only produces burgers (1 patty & 1 bun). In particular, the GRILL can produce 15 patties in 4 minutes. The PLATEN can produce 20 buns in 4 minutes. A worker in ASSEMBLY can assemble 1 burger in 10 seconds. One worker at the COUNTER can give 1 burger to a customer in 1 minute. There are 4 workers in COUNTER operations and 1 worker in ASSEMBLY. Which is the total capacity of the process? Answer in Burgers per hour please

10.2 A panel of 30 rooms in a room-and-pillar coal mine is to be driven from a set of three room entries connecting to panel entries. The rooms an driven on 100 ft (30 m) centers; they are 16 ft (4.8 m) in width and 300f (90 m) in length. Room entries are also 16 ft (4,8 m) in width on 100f (30 m) centers. Crosscuts between both rooms and entries are placed 10.2 A panel of 30 rooms in a room-and-pillar coal mine is to be driven from a set of three room entries connecting to panel entries. The rooms an driven on 100 ft (30 m) centers; they are 16 ft (4.8 m) in width and 300f (90 m) in length. Room entries are also 16 ft (4,8 m) in width on 100f (30 m) centers. Crosscuts between both rooms and entries are placed on 100 ft (30 m) centers. A barrier pillar 100 ft (30 m) in width will b left on three sides of the panel. A sketch of the mining plan appears in Figure 10.18. Compute the percentage recovery for the mining panel n each of the following cases: a. No pillar recovery b. Recovery of chain pillars in rooms and entries c. Room width increased to 20 ft (6 m) and no pillar recovery

Air at 80 degrees Fahrenheit and 14.7 psia with a mass flow rate of 0.6 lbm/sec enters a compressor and leaves at 70 psia and 430 degrees Fahrenheit through an exit area of 0.007 ft^2.  The measured heat interaction rate with the 80 degree Fahrenheit factory room is 3 Btu/sec.  Use constant Cp = 0.24 Btu/lbm oF a) Calculate the compressor work rate.   b) Compute the entropy generation rate for the overall process.  

1 Required information A 20-mm-diameter rod made of the same material as rods AC and AD in the truss shown was tested to failure and an ultimate load of 105 kN was recorded. Use a factor of safety of 3.0. Part 1 of 2 1,5 m D B 3 m -3 m 48 kN 48 kN Determine the required diameter of rod AC. The required diameter of rod AC is mm.

Required information A 20-mm-diameter rod made of the same material as rods AC and AD in the truss shown was tested to failure and an ultimate load of 125 kN was recorded. Use a factor of safety of 3.0. 1.5 m 3 m 48 KN 48 KN Determine the required diameter of rod AC. The required diameter of rod AC is mm

thermo 2 help plz Air, at \( 80^{\circ} \mathrm{F} \) and \( 14.7 \) psia with a mass flow rate of \( 0.6 \mathrm{Ibrm} / \mathrm{sec} \) enters a compressor and leaves at 70 psia and \( 430^{\circ} \) F through an exit of area 0007 . th \( ^{2} \). The measured heat internction rate with the \( 80^{\circ} \mathrm{F} \) factory room is \( ₹ \mathrm{Bth} / \mathrm{sec} \). Use constant \( \mathrm{C}_{p}=0.24 \mathrm{Btw}_{\mathrm{f}} \mathrm{b}_{\mathrm{m}}{ }^{\circ \mathrm{F}} \) a. Calculate the compressor work rate, W. b. Compute the entropy generation rate for the overall process.

Required information Problem 15-4A (Algo) Preparing job cost sheets, recording costs, preparing inventory ledger accounts LO P1, P2, P3 [The following information applies to the questions displayed below] Watercraft's predetermined overhead rate is 200% of direct labor. Information on the company's production activities during May follows. a. Purchased raw Required information Problem 15-4A (Algo) Preparing job cost sheets, recording costs, preparing inventory ledger accounts LO P1, P2, P3 [The following information applies to the questions displayed below] Watercraft's predetermined overhead rate is 200% of direct labor. Information on the company's production activities during May follows. a. Purchased raw materials on credit, $220,000 b. Materials requisitions record use of the following materials for the month. Job 136 Job 137 Job 138 Job 139 Job 140 Total direct materials Indirect materials Total materials requisitions Job 136 Job 137 30h 138 300 119 $ 49,500 32,500 19,400 c. Time tickets record use of the following labor for the month. These wages were paid in cash Job 140 Total direct labor Indirect labor Total labor cost 23,200 6,400 131,000 20,500 $ 151,500 $ 12,300 10,500 37,900 39,200 4,000 101,900 14,500 $ 128,400 Journal entry worksheet < 3 Record raw material purchases on credit. Note: Enter debits before credits. Transaction Record entry 4 Raw materials inventory Accounts payable General Journal 5 Clear entry 6 7 8 Debit 220,000 ***** Credit 11 220,000 View general journal >