Liew and Ramzi are travelling in their respective rockets towards each other as shown in Figure 1. A measurement done by Noraza, a mission controller on earth, showed the following data:

Variables	Liew’s Rocket	Ramzi’s rocket
Speed	0.8c	0.6c
Length	50 m	80 m

1. According to Liew, what is the
   
   1. length of Ramzi’s rocket?
      
   2. velocity of Ramzi’s rocket?
      
2. During the measurement, Noraza found that the rockets are 2.52 _× 10¹² m away from each other. If Ramzi has only 90 minutes to save himself and Liew, will there be a tragic loss of lives? Justify your answer.
   

Using LC-3 Programming Exercise 1 Use .BLKW to set up a remote array of 10 values, starting at memory location x4000, as in lab 3. Now programmatically populate the array with the numbers 0 through 9 (note - NOT the characters '0' through '9'!) – i.e. hard-code just the first value (0), then calculate the rest one at a time, storing them in the array as you go. Remember the proper way of setting a register to 0! After you've stored them all, grab the seventh value (i.e. 6) and store it in R2. Clearly, you can't access this location via a label, so you'll need its actual address. How will you obtain that? And how will you use that address to get the value stored there? As always, step through your program and examine the values as they are stored in the array, and examine the final value stored in R2, to make sure your program works as expected. Exercise 2 You'll notice that Exercise 1 didn't ask you to output to console the array you built. Why not? Because as you know by now, numbers are not characters! So now copy your exercise 1 code into lab4_ex2.asm, and add an output loop, making it output the characters corresponding to the numbers stored in your array. Exercise 3 Let's try another modification of our well-used array program from Exercise 1: This time, instead of calculating and storing the numbers from 0 to 9 in the array, calculate and store the first ten powers of 2, starting with 20 = 1 in array index 0. Finally, grab the seventh value (26) from the array, and store it in R2. In order to do this, you will have to figure out how to calculate powers of 2. Some hints: Mathematically speaking: How do I obtain 2n+1 if I know 2n? What LC-3 operation could I use to multiply a number by 2? As always, place a breakpoint in your program, and step through it, examining the values as they are being stored in the array, and examine the final value stored in R2,  to make sure your program works as expected. Pay attention to both the decimal and hex representations of the values being stored. You already understand that you can't simply output the values in the array to the console “as is”, so we have to manipulate them somehow to turn them into characters. But this time all but the first four are multi-digit numbers when represented as decimal values, so our trick from the last exercise won't work – it can only convert the numbers from 0 to 9 into the single-digit ascii characters '0' through '9'.  Exercise 4 For now, we will instead observe what happens if we attempt to do what we just said can't be done - output the contents of the array "as is", i.e. as if they were ascii codes (which they are not!). Copy your exercise 3 code into your lab4_ex4.asm file, and add a second loop that loads the content of each element of the array into R0 and outputs it to the console using OUT. Now place a breakpoint at the start of your display loop and step through it: You will need to keep an eye on the Console to understand what is going on!! Please add comments!!!

7. The number of surface flaws in plastic panels used in the interior of automobiles has a Poisson distribution with mean of 0.04 flaws per square foot of plastic panel. Assume automobile interior contains 10 square feet of plastic panel.(a) What is the probability that there are no surface flaws in an auto's interior?(b) If 10 cars are sold to a rental company, what is the probability that none of the 10 cars has any surface flaws?(c) If 10 cars are sold to a rental company, what is the probability that at most two cars have any surface flaws?

QN ; Compare [ a construction company ] against TEN of the requirements of the audit standard given in supporting document below. [ 30 marks ] 1.0 PlanningRequirements:1.1Establish audit programme.1.2Selection of and checks on competence of audit lead.1.3Establish the scope of the audit.1.4Set procedures for the

Complete MS Project Exercise 2 on Appendix A: Brief Guide to Microsoft Project Professional 2016 2. Continue performing the steps in this appendix, starting with the section called Developing the Schedule. Print out the following screens or send them to your instructor, as directed: a. Figure A-32. All task durations and recurring task entered b. Figure A-39. Network diagram view c. Figure A-46. Changing Work hours for tasks d. Figure A-56. Earned value report e. Continue performing the steps, or at least read them. Write a one-to-two page paper describing the capabilities of Project Professional 2016 and your opinion of this software. What do you like and dislike about it?

Continue performing the steps in this appendix, starting withthe section called Developing theSchedule. Print out the following screens or send them to yourinstructor, as directed:a. Figure A-32. All task durations and recurring task enteredb. Figure A-39. Network diagram viewc. Figure A-46. Changing Work hours for tasksd. Figure A-56. Earned value

Refer to the case “Blue Ocean Leadership: How to Achieve High Impact at Low Cost”, and answer the following questions: 1. Revise your time/effort ratings and the order of the acts and activities according to the results of the Leadership Grid and transfer the data to the To-Be Leadership Canvas.