Question Read the following summary written as an introduction to an analyss assignment Early in the story we meet Nixon, a sixty year old carpenter. Although his family doesn't know it, he is battling lung cancer. This story is the sixth of a series by the author, all about people living in the midwestern United States. Nixon is determined to continue working and providing for his family, regardless of his worsening health Which sentence provides unnecessary details given the purpose of the assignment? Select the best answer Answer Keypad Keyboard Shortcuts Click on a word or word group to make a selection. To undo, click on the selection again, Alternatively use the Tab and spacebar to select or deselect the word or word group Clear Early in the story we meet Nixon, a sixty-year old carpenter. Although his family doesn't know it, he is battling lung cancer. This story is the sixth of a series by the author, all about people living in the midwestern United States, Nixon is determined to continue working and providing for his family, regardless of his worsening health

Mason Company has two manufacturing departments ---Machining and Assembly. The company considers all of its manufacturing overhead costs to be fixed costs. It provided the following estimates at the beginning of the year as well as the following information with respect to Jobs A and B: Estimated Data Machining Assembly Total Manufacturing overhead $ 500,000 $ 100,000 $ 600,000 Direct labor hours 10,000 50,000 60,000 Machine hours 50,000 5,000 55,000 JobA Direct labor hours Machine hours Machining Assembly Total 5 10 15 11 2 13 Machining Assembly Total Job B Direct labor hours Machine hours 4 12 3 9 15 Required: 1. if Mason Company uses a plantwide predetermined overhead rate with direct labor-hours as the allocation base, how much manufacturing overhead cost would be applied to Job A? Job B? 2. Assume that Mason Company uses departmental predetermined overhead rates. The Machining Department is allocated based on machine-hours and the Assembly Department is allocated based on direct labor-hours. How much manufacturing overhead cost would be applied to Job A? Job B? 1. Manufacturing overhead applied Job AS Manufacturing overhead applied Jobs 2 Manufacturing overhead applied Job A Manufacturing overhead applied Job B 125 75

Coursework 3.3 Write the state-space representation for the following systems: Yilt 7. 421t) К. M2 KI m W fit) bi yait) be -Ma RA 2. 20 + yilt) Ta í It) = Uzlt) Milt=VLE R2 R2

Help please A thin walled cylindrical pressure vessel is subjected to an internal pressure which varies from 750 KPa to 3550 KPa continuously. The diameter of the shell is 1.5 m. Find the required thickness of the cylinder wall based on yield point of 480 MPa, net endurance limit of 205 MPa and a factor of safety of 2.5. A camshaft 19 mm. in diameter is mounted on ball bearings and carries a cam midway from the bearings. The follower, which weighs 2.8 KN, is out of adjustment so that impact is produced when it is contacted by the cam. The height h of fall equals 0.254 mm. The shaft is made of AISI C1045 steel. Determine the maximum bending stress in the shaft.

Consider the following diagram: Internet Modem Wireless AP Switch Wireless AP DO Wireless AP Server 2.1 Using a table, compare 4 types of area networks. Consider the size of the network and the transmission media that is most likely to be found in each type of network. (8) 2.2 Based on the information given in 2.1, which type if network is shown in the Consider the following diagram: Internet Modem Wireless AP Switch Wireless AP DO Wireless AP Server 2.1 Using a table, compare 4 types of area networks. Consider the size of the network and the transmission media that is most likely to be found in each type of network. (8) 2.2 Based on the information given in 2.1, which type if network is shown in the diagram? Motivate your (2) answer. 2.3 This network has wireless access points. Compare three modulation techniques, using sketches, that could be used by these access points to transmit data. Use the bit-stream 10000101111. (6)

P3.5 The sales revenue, food cost of sales, and guests served for a small fast- food carryout division of a restaurant for the past six months are given below. Sales Month Cost of Revenue Guests Served Sales, Food 1 2. 4 $258,200 274,800 285,600 289,400 298,300 304,600 $ 96,200 104,300 110,500 113,100 118,900 123,700 10,200 10,400 10,300 10,100 10,400 10,500 6 For each of the six months calculate average check and average costs of sales food. Using these averages, calculate an index number. Set the in- dex for month 1 at 100 and complete index numbers for the remaining five months. With the index numbers identified, convert sales revenue and cost of sales food from historic to current dollars.

A cylindrical rock sample has a length of 6 cm, a diameter of 4 cm, and a dry weight of 166.4 g. When fully saturated with an oil of density 0.85 g/cm3, the weight of this sample is 176.9 g. Assuming constant temperature, find: i) The porosity of the sample ii) The pore compressibility of the sample, given that 0.2 cm of oil leaves the sample when a pressure of 3200 psig is applied on it iii) The amount of oil that can be extracted from the sample when a pressure of 2000 psig is applied on it