Question The loaded trailer has a mass of 900 kg with center of mass at G and is attached at A to a rear-bumper hitch. If the car and trailer reach a velocity 60 km/h on a level road in a distance of 30 m from rest with constant acceleration, compute the vertical component of the force supported by the hitch a: A Neglect the small friction force exerted on the relatively light wheels.

Water vapor enters a turbine operating at steady state at 1000°F, 220 lbf/in2, with a volumetric flow rate of 25 ft3/s, and expands reversibly and adiabatically to 2 lbf/in? Ignore kinetic and potential energy effects. Determine the mass flow rate, in lb/s, and the power developed by the turbine, in hp. Step 1 Determine the mass flow rate, in lb/s. m = i lb/s Save for Later Attempts: 0 of 4 used Submit Answer

14.1 Match the terms in the left column with their definitions from the right column: 1. Bill of materials a. A factor that causes costs to change 2. Operations list b. A measure of the number of good units produced in a period of time c. A list of the raw materials used to create a finished product 3. Master production schedule 4. Lean manufacturing d. A document used to authorize removal of raw materials from inventory 5. Production order e. A cost accounting method that assigns costs to products based on specific processes performed 6. Materials requisition f. A cost accounting method that assigns costs to specific batches or production runs and is used when the product or service consists of uniquely identifiable items 7. Move ticket g. A cost accounting method that assigns costs to each step or work center and then calculates the average cost for all products that passed through that step or work center 8. Job-time ticket h. A document that records labor costs associated with manufacturing a product 9. Job-order costing i. A document that tracks transfer of inventory from one work center to another 10. Cost driver j. A document that authorizes manufacture of a finished good 11. Throughput k. A document that lists the steps required to manufacture a finished good 1. A document that specifies how much of a finished good is to be produced during a specific time period 12. Computer-integrated manufacturing m. A production planning technique that is an extension of the just-in-time inventory control method n. A production planning technique that is an extension of the materials requirement planning inventory control method o. A term used to refer to the use of robots and other IT techniques as part of the production process

11.60 Consider the flow of air through the piping system shown in Fig. P11.60. If the system is choked, determine the location where the Mach number is 1. Calculate the pressure ratio pb/Po, that causes choking in this system. 100 in 100 in Pв PO то 4 1.5 in diameter 1 in diameter Short nozzle 0.0030 in 1.5 in pipe 0.0035 in 1 in pipe

The worldwide market share for the Chrome web browser was 56.43% in a recent month. Suppose that you decide to select a sample of 100 students at your university and you find that 60 use the Chrome web browser. a. Use the five-step p-value approach to determine whether there is evidence that the market share for the Chrome web browser at your university is greater than the worldwide market share of 56.43%. (Use the 0.05 level of significance.) b. Suppose that the sample size is n = 600, and you find that 60% of the sample of students at your university (360 out of 600) use the Chrome web browser. Use the five-step p-value approach to try to determine whether there is evidence that the market share for the Chrome web browser at your university is greater than the worldwide market share of 56.43%. (Use the 0.05 level of significance.) c. Discuss the effect that sample size has on hypothesis testing. d. What do you think are your chances of rejecting any null hypothesis concerning a population proportion if a sample size of n = 20 is used?

Find the magnitude of the resultant force and the angle it makes with the positive x-axis. (Let a = 26 lb and b = 12 lb. Round your answers to one decimal place.) Find the magnitude of the resultant force and the angle it makes with the positive x-axis. (Let a = 26 lb and b = 12 lb. Round your answers to one decimal place.)

Harley-Davidson is known for its strong brand name and loyal following and yet by 1980 Harley was on the verge of bankruptcy. Why was Harley in deep trouble even with such a strong brand name? a) Harley-Davidson cannot compete in foreign markets b) Competitors beat Harley on reliability and cost c) All of the above d) Harley-Davidson bikes are technologically inferior COURSE: STRATEGIC BUSINESS DECISIONS